Buyezrip Magazine – Car Cleaning

car cleaningWhether you are paying for car wash service or you just consider doing it yourself, the entire process should be done with caution. Your car is a big investment that needs to be treasured, and probably this is something you already know. However, car washing pros use rotating buffers to clean and resurface the car paint with charcoal coated foam lags or wool pads. These machines are not meant to be used by anyone unless you are an experienced person with several years in the industry.

If you want your car to glow and ensure fine finishing is done professionally, take some of your precious time specifically for that job. Don’t just wake up in the Saturday morning and start detailing your car without proper planning. If you feel the project is somehow overwhelming, don’t hesitate to drive the car to a nearest car wash station.

But if you have the self-confidence to handle it, here are the tips to get you started.

Assess the interior and exterior of your car

Both interior and exterior of your car require equal care. The interior areas to be emphasized include rugs, dashboard, handles, carpet, and headliner. For the exterior, ensure the roof, hood, tires, and wheels are worked on. As I said earlier, you need to spare time for this job. Either the exterior or interior can start, but next day ensure you examine the few areas you missed.

Begin with an air compressor and a stiff brush

Firing an air compressor onto the crannies and nooks will blow the stuck dirt on the car’s floor onto the center of the carpets. When the dirt is collectively settled on the carpets, you can use a vacuum machine to empty it easily. Pick a stiff brush to loosen dirt from the upholsteries and carpets. However, an aloe conditioner is ideal for leather seats.

Bring some new smell by cleaning the ducts

Use a small air compressor to blow dirt and dust out of the air conditioning and heating ducts. Ensure a high-pressure air is directed to the duct walls at the back of vent grilles where dirt sticks and cause moldy smell. If the car has a cabin air filter, pull it down and blow the dirt out. This creates a new fresh smell in your car. If you need a different scent, there are different types of car fresheners in the market to choose from.

Clean car tires with non-acid based cleaners

cleaning the tyresThe experts usually use mixed acid solution for tire cleaning, as well as for stripping scum if your car has new tires. Brakes are also responsible for dust buildup on wheels, and the mixed acid solution helps get rid of the dust. If you are cleaning a car on your own, it is advisable to use non-acid products to prevent oxidation of the alloy wheels and damaging of original wheel paint or coating. So, a degreaser is suitable for your alloy wheels.

Apply both hand wash and pressure wash

Hand washing is required so that you can feel the car’s shape and familiarize with its surface. Air pressure washer is also ideal to clean those hard-to-reach areas, especially along the edges. But note that, dishwashing detergents can strip protective wax coating and expose your car to scratches and stains. So, use car wash solutions to preserve your car’s original finish.

Clean your car’s paint

This requires more than just a typical washing. You can determine whether your car needs paint wash by running your hand over the surface when dry. If it is rough, thorough cleaning is needed. You can use paint cleaners to remove scratched old wax and other chemicals bonding with your car’s paint. Rubbing physically using clay cleaner mixed with a lubricator wax cleaner is also a good option.

Polish for a shinier look

Polish for a shinier lookPolishing makes your car appear newer. You can use wax polishes or an oscillating polishing machine if you have it. At most car wash centers, the experts use the oscillating polishing machine. However, the machine has some bit of learning curve. So, ensure you know how to use it because it can destroy the paint if not appropriately used.

In conclusion, it is good to pay for car detailing and washing service if the paint is scratched down deep to the metal. The job requires a professional sanding and filling the scrapes. Experts can handle this kind of task and ensure the paint is blended well with the rest of the surface. Source: Car Outfitter.

Office Chair, Posture, and Driving Ergonomics

Did you know that office chair may be the cause of your back pains? The structure of the spine is complex, and it is made of several discs that run throughout the back. If the structure is altered, back pain is likely to develop. Basically, posture is the core determinant of whether or not you will experience back pain.

Ergonomic Office Chair Posture

Spine is naturally curved, and it can be maintained through proper sitting posture. Ergonomic chairs have been designed to offer comfortable sitting experience, ensuring your chest is protruding outwards and the head directly over the shoulders. The shoulders are aligned directly with the upper abdomen, while the abdominal muscles are kept tight. The buttocks are tucked as the thighs are maintained perpendicular to the spine. Knees are slightly bent, and a little bit spreading the feet.

ergonomic-chair-product

Sitting on ergonomic office chairs keeps the body aligned with the head, arms, thighs, legs, as well as feet. This is what is referred to as ‘good posture’, whereby all other body parts are in support to one another. When working in an office for about 8 hours on daily basis, you are likely to have bad posture on different occasions. This can lead to lower back strain, especially if the chair is not fitted with new ergonomic features. Remember, an ergonomic office chair should offer full lower back support.

Spending hours in front of an office computer can result to back pain, despite the level of comfort provided by your chair. You should adjust the chair and desk regularly, in order to change the sitting posture. Slumping or slouching is another cause of serious backaches, because people tend to get near the screen when they are tired. Your head and neck should stay straight throughout, but you can stand up and stretch whenever you feel tired.

When buying a new office chair, it is advisable to choose ergonomic types that offer maximum comfort. The office desk should be adjustable such that you can change the position of the screen in order to have an ideal eye gaze while working. Your hands should rest on the desk, while the shoulders are supported by an armrest right at the lower arms. Your feet should be flat resting on the floor, while the knees are slightly bent.

Ergonomic driving posture

People who drive to and from work every day are likely to have back pains due to their driving posture. Driving for more than an hour can strain the neck and both lower and upper spine. However, perhaps it is difficult to get a car with an ideal seating specifically for you. Unusually tall people may experience back straining while driving compact cars because the seats may not fit them properly. However, it is recommended not to adjust the car driving seat such that you cannot use front windscreen and your side mirrors properly.

Before you start driving, ensure the hips and knees are at the same level. If the car seat does not offer this posture, place a cushion between your back and the backseat to enhance the comfort. The steering wheel and the driver should allow a fair distance so that you can stretch your lower arms, while the upper arms are aligned with the spine. But you should not sit too far from the steering wheel because too much stretching to reach may cause back strain.

If you stay keen on your sitting or driving posture, you will eliminate some problems that arise as a result of back straining. Good posture indicates reliable support on the lower and upper back, and therefore reduce the neck and back pains. If you spend several hours in the office or you drive an hour every day, ensure good posture is maintained always.

Read our posts related other home-office furnitures: garbage disposals  and gun safes.

How to Install a Toilet by Yourself?

Whether you are planning to set up or replace an existing toilet, it is always tempting to call in a plumber to do all the dirty work for you. While this sounds like a very convenient choice, it is not impossible for you to do this task by yourself. Given the right tools and instructions, you can easily give your toilet a makeover without spending cash on plumbing services.

What you need

Preparation is the key to a smooth and organized installation of your toilet. To start with, you will need a good quality toilet that could last many years. Next, you have to buy a wax ring to close any gaps between the flange and the lower end of the toilet. Other essentials are closet bolts to fasten your toilet to the flange, toilet connectors for the water supply, a soil pipe, and PVC cement. Additional materials include steel washers, a torpedo level to make sure that your toilet is at a perfect angle, an adjustable wrench and a screwdriver. All these materials are readily available at hardware and plumbing supply outlets.

Installation Process

Before anything else, prepare the bathroom floor by checking the measurement ohow to install a toiletf the hole to make sure that the closet flange can fit in snugly up to its neck. After inserting the flange to the soil pipe, connect the soil pipe to the closet bend and apply PVC primer on its inner portion, as well as on one outer end of the soil pipe. Once this is done, PVC cement should be applied to the exact areas and rotate the pipe in the closet bend without delay to avoid hardening of the cement. Repeat the same procedure on the exposed areas of the soil pipe and closet bend then insert the flange onto the soil pipe. Rotate and apply pressure until the collar is settled and fitted on the floor. The slots must be in its proper position on the floor and should be parallel to the wall where the tank will be situated.

Prepare the closet bolts and position them on the slots on both sides, followed by the steel washers. After this, place the wax ring on top of the flange so that it will not be dislodged while placing the toilet. Extended-height rings are available if the flange is too low on the ground. Finally, it is time to position the toilet onto the flange by checking that either holes are properly aligned with the bolts. Once it is placed, carefully push down the toilet towards the ground. When the toilet is firmly attached to the ground, place the washers above the closet bolts then twist the nuts on either side and make sure it is tight.

Inspect the toilet if it is equally leveled otherwise insert steel washers or plastic shims to prevent it from rocking. After tightening the nuts with a wrench, cover the bolts with bolt caps.

Finally, connect the toilet to the water supply line using the toilet connector and twist open the valve so water can fill the tank. Make sure that the water meets the appropriate fill line simply by adjusting the fill valve.

Easy Tips and Tricks

Executing this little do-it-yourself project can become quite challenging especially for first-timers so it would be extra helpful to remember these tips to make it more hassle-free. When buying a toilet, it would be best not to buy models that use below 6 liters of water for each flush. Also, ask for self-adjusting closet bolts that are available in plumbing stores to avoid the stress of having to cut the extra length. Next, you need to be quick and efficient when aligning the slots after applying the cement on the flange or else, you will end up with dried cement.

Most people prefer assembling the toilet before anything else so that it is readily available during installation. If you are alone and cannot handle the weight of the tank while installing the toilet, you can attach it later. Review everything for any misplaced items and do not tighten the nuts excessively as they can cause damage to the porcelain.

If you are trying to level the toilet, plastic shims are available although it is much better to use steel washers instead as they are stronger and does not crack.

For those who want their toilet base to appear more clean and polished, you can opt to caulk it, however you must leave a little space in the back portion to help you detect any leaks and act on it sooner. For more DIY installation, check HOW-TO category. If you haven’t bought your toilet yet, click to see comparison of toilets in pickatoilet.com.

 

How to Install a Garbage Disposal ?

Take time to consider the major factors when purchasing a disposal unit. 

Are you more concerned with convenience or safety? 

If you don’t have young children around and you want convenience then you should choose a continuous feed system.  This is because you will be able to clean your kitchen of food waste very easily, while doing other work around the kitchen.  Now of course there is a danger to using a continuous feed system, as the name suggests when you turn the power on the unit will run continuously, so anything that falls into the unit will be attacked by the unit.  So you have to be careful around it and make sure no foreign objects that you don’t intend on mulching fall into it and you have to obviously watch your fingers.  If you’re worried for a moment about staying safe or having little people around that might get hurt, then go with a batch-feed which is a less convenient system that has the safety feature of only running in batches.

Looking for the disposal power

Consider the power of the disposal that you’re going to buy.  Make sure that you get a disposal that is powerful enough to mulch up the food waste you intend on putting into it.  Make sure that the noise profile of the machine isn’t going to be too loud for your tastes and consider what kind of plumbing you have.  If you have a septic system, be sure to make sure that your disposal is compatible with it.

 

Once you’ve made your purchase you should gather up the equipment and supplies you will need for a do-it-yourself installation.  You’re going to need to make sure that you have goggles and a dust mask while you work; Safety First!   You’ll need water pump pliers, plumber’s putty, electrical cord, a hacksaw, a garbage disposal wrench and screwdrivers.

The most important is the safety

Again safety is tremendously important when dealing with a unit meant for causing destruction, so make sure that the power is off before continuing and cover the power panel to make sure nobody else can turn the unit on while you’re working on it.

 

If your unit is attached to your dishwasher, then you’re going to want to detach it.  Use a screwdriver to remove the hose that is attached to the dishwasher from your disposal unit.  Next you’ll want to remove the trap waste line that is going from the disposal unit by using your wrench to unscrew the nut which connects the disposal and the trap.  Make sure that you utilize something to catch any waste that remains inside the unit because when you remove these two parts you’re going to drip waste, so have a bucket or some other catcher.

Remove the disposal from the mounting structure.  Use your screwdriver to loosen and remove the old disposal.  Now disassemble the rest of the mounting structure by removing the ring on the sink sleeve, the flange and the fiber gasket as well as the old plumber’s putty.

Once the old disposal and assembly is away, you can install your new unit.  You’re going to want to wire up your unit properly, follow the expert websites detailed instructions like disposalmag.com.  Now you’ll want to prepare the new mounting structure by installing the drain flange and mounting ring.  Prepare some Plumber’s Putty by rolling it between your hands to form a snake that is about 10 inches long and about half an inch thick.  Run it around the underside of the drain flange under the sink.  Insert the flange into the drain and apply enough even pressure to attach it properly.  After this you will simply pop on the mounting ring, fiber gasket, and backup rings just as you had them with the previous model.  You’re essentially just redoing everything that existed before, but fresh parts for your new model.

 

Sometimes it can help when doing installs such as these to take good notes of the removal process for the old unit, that way you can replicate, but in reverse for any new units.  This is important for a lot of plumbing work.

 

Now mount the disposal and attach the trap again, making sure all parts are secure.  Make sure that you pay attention to the manufacturer’s instructions as you go.  If you have a dishwasher and dishwasher attachment make sure to reattach it and now you can test your disposal.  Make sure that you give your new disposal a thorough test to ensure that there is no leaking at all and that you’ve sealed everything properly. For more DIY improvement click here.

 

Every Home needs a Fireproof Safe

Gun enthusiasts are always urged to take good care of their guns and to prevent unauthorized access and use. While both of these can be achieved using a standard gun safe, it is also quite important to consider fire resistant gun safes.

Fire outbreaks are quite common and in case a gun safe is caught in one, the ammunition and the firearms should be protected till the fire can be extinguished. When looking to purchase a fireproof safe, make sure to check the reliability of the safe, which is usually mentioned in the specifications as to whether the safe meets safety regulations and also the limit of resistance of the safe to fire.

Typical things to consider in a fireproof safe include the following:

  • The fire endurance rating of the safe
  • The type of insulation from fire
  • The thickness of the fire insulation

Fireproof gun safes are typically secure and most of them need to be clamped down to the floor. While these fire resistant safes were more expensive in the past, there are a number of budget friendly and affordable safes in the market today. Beginner models can start off at a price of less than $200 while the high end models reach the $1000 mark.

How to install a Shower Head?

Rain-shower-headWe always feel like replacing the shower head after a few years of installing it and the reasons behind this are many like you want a new different style show head. Or the one that you are already having is not able to dispense water properly due to some internal problem or it could even be that you are in love with the head shower that you saw in your colleagues’ bathroom. Let the reason behind your wish to install a new shower head be whatsoever. Here are few things for you to do before you embark on this task. These are very simple. Have a look at these 4 steps to understand them better.

  1. Firstly, you will have to make sure that the shower arm is in good condition or do you want to replace that as well. It should also match with the look and finish of the new shower head that you are going to install. If you are fine with the existing one, then start with the installation of new shower head.
  2. The next step is you need to wrap the thread seal tape to the shower arm’s base.
  3. Now, place the shower head in position and start turning it, till it gets placed correctly. Make sure that you are not making it too tight; else it will get damaged very fast.
  4. If you are going for a hand held shower head, then you need not have to use the thread seal tape at the base of shower arm. You can directly thread it inside the shower arm.

Nowadays, hand held shower heads are more in use, as its installation does not require more time and usage is also easy. You will be able to move it as per your requirement, which is not possible with a wall mounted shower head. So, choose the one that suits your daily requirement and your budget. You can check best shower head reviews here on www.finestshower.com

 

 

After the installation is done, the work is not complete yet. Once the installation is done, you need to open the shower water toshower-heads check for any kind of leakage. If the water is not leaking, then it is good to go. But if it is leaking, then you should make sure that you are re-tightening the shower head near the shower arm. If the problem is still persisting, then you should remove the shower head and make sure that the thread seal tape is wrapped properly, failing which there are chances of water leakage. Apply 5 to 6 rounds of thread seal tape to the shower arm base.

This is a very simple process and can be done by yourself at home. You don’t need to spend money for its installation. All you will need is a good and a new shower head and thread seal tape of good quality. You will need a new shower arm pipe and putty to seal the wall, in case you are going for replacing the shower arm as well.